关闭
点击这里给我发消息
点击这里给我发消息
 +86 0512-62751429
+86 13416743702
您好,欢迎您来到:苏州市宇顺力电子有限公司官网!服务热线:0512-62751429.
YUSH Electronic
新闻动态
走刀式分板机该如何进行调试
找东莞走刀式分板机厂家,推荐东莞市宇顺力自动化设备有限公司,公司主营 激光分板机、PCB分板机、铝基板分板机、LED灯带分板机、多刀分板机、走刀分板机、分板机、铡刀分板机、冲床分板机、铣刀分板机、横竖方向分板机、邮票孔分板机、在线锣板机、离线锣板机、曲线分板机、FR4分板机、FPC分板机等,欢迎电话咨询
走刀式分板机通电通气的状态下,踩下脚踏开关,上刀压下时, 此时松开手滑阀,然后再松开脚踏开关, 使上刀停在底部. 用4mm 六角匙调节捌个无头螺丝, 调到下刀与上刀平行,确定平行后锁紧5个压刀螺钉。
Under the condition of power supply and ventilation, step on the foot switch. When the upper knife is pressed down, release the hand slide valve, and then release the foot switch to stop the upper knife at the bottom. Use a 4mm hexagon key to adjust eight headless screws until the lower cutter is parallel to the upper one, and then lock the five knife pressing screws.
在分切普遍的基板时,中的上下刀A,B两平面位于同一平面.若分切韧性较强的产品.可将上图中的4个螺丝C松开.将下刀及其刀架同时向左调节,调节范围不宜超过0.1MM.尔后将下刀上调0.10—0.20MM,使上下切刀产生一定的交叉.从而将产品分切开(调节过程中要踩着脚踏,防止调节过量从而造成上下切刀的崩裂)调节之后将螺钉C锁紧。新机器在分切一段时间之后,可能会出现分不开的情况,可先踩着脚踏开关,将的八个无头螺钉均匀向下顶,使下刀上升.单次调节量不超过0.1MM为宜.防止上下刀相撞。
When cutting common substrates, the upper and lower blades a and B are located on the same plane. For products with strong cutting toughness, loosen the four screws C in the figure above. Adjust the lower cutter and its holder to the left at the same time, and the adjustment range should not exceed 0.1 mm. Then, adjust the lower knife by 0.10-0.20 mm to make the upper and lower cutters intersect to a certain extent, After adjustment, screw C is locked. After the new machine is cut for a period of time, it may not be separated. Step on the foot switch and push the eight headless screws down evenly to make the lower knife rise. The single adjustment should not exceed 0.1 mm to prevent the upper and lower knives from colliding.
想了解更多关于走刀分板机 多刀分板机 离线锣板机信息推荐我们的网站:www.13450659407.com
产品分类
                                        当前位置: 首页 -> 新闻动态

                                        走刀式分板机该如何进行调试


                                        找东莞走刀式分板机厂家,推荐东莞市宇顺力自动化设备有限公司,公司主营 激光分板机、PCB分板机、铝基板分板机、LED灯带分板机、多刀分板机、走刀分板机、分板机、铡刀分板机、冲床分板机、铣刀分板机、横竖方向分板机、邮票孔分板机、在线锣板机、离线锣板机、曲线分板机、FR4分板机、FPC分板机等,欢迎电话咨询
                                        走刀式分板机通电通气的状态下,踩下脚踏开关,上刀压下时, 此时松开手滑阀,然后再松开脚踏开关, 使上刀停在底部. 用4mm 六角匙调节捌个无头螺丝, 调到下刀与上刀平行,确定平行后锁紧5个压刀螺钉。
                                        Under the condition of power supply and ventilation, step on the foot switch. When the upper knife is pressed down, release the hand slide valve, and then release the foot switch to stop the upper knife at the bottom. Use a 4mm hexagon key to adjust eight headless screws until the lower cutter is parallel to the upper one, and then lock the five knife pressing screws.
                                        在分切普遍的基板时,中的上下刀A,B两平面位于同一平面.若分切韧性较强的产品.可将上图中的4个螺丝C松开.将下刀及其刀架同时向左调节,调节范围不宜超过0.1MM.尔后将下刀上调0.10—0.20MM,使上下切刀产生一定的交叉.从而将产品分切开(调节过程中要踩着脚踏,防止调节过量从而造成上下切刀的崩裂)调节之后将螺钉C锁紧。新机器在分切一段时间之后,可能会出现分不开的情况,可先踩着脚踏开关,将的八个无头螺钉均匀向下顶,使下刀上升.单次调节量不超过0.1MM为宜.防止上下刀相撞。
                                        When cutting common substrates, the upper and lower blades a and B are located on the same plane. For products with strong cutting toughness, loosen the four screws C in the figure above. Adjust the lower cutter and its holder to the left at the same time, and the adjustment range should not exceed 0.1 mm. Then, adjust the lower knife by 0.10-0.20 mm to make the upper and lower cutters intersect to a certain extent, After adjustment, screw C is locked. After the new machine is cut for a period of time, it may not be separated. Step on the foot switch and push the eight headless screws down evenly to make the lower knife rise. The single adjustment should not exceed 0.1 mm to prevent the upper and lower knives from colliding.
                                        想了解更多关于走刀分板机 多刀分板机 离线锣板机信息推荐我们的网站:www.13450659407.com
                                        苏州宇顺力电子有限公司 版权所有 @ Copyright 2015 联系人:刘小姐 地址:江苏省苏州市昆山市金阳东路1068号(国瑞产业园)*本站相关网页素材及相关资源均来源互联网,如有侵权请速告知,我们将会在24小时内删除* 《中华人民共和国电信与信息服务业务经营许可证》编号:苏ICP备14049770号-5
                                        联系我们
                                        #字型分板机华南地址:
                                        冲床分板机地址:广东省东莞市涌头村山泉路十号(总部)
                                        软板分板机咨询:13862072520
                                        PCB Router分板机电话:0769-88087410
                                        走刀分板机网址:http://www.szfbj.com
                                        华东在线分板机地址:
                                        全自动分板机地址:江苏省苏州市昆山市金阳东路1068号(国瑞产业园)
                                        邮票孔分板机电话:0512-62751429
                                        咨询基板分板机:13450659407
                                        裁切分板机邮箱:seles@hk-yush.com
                                        led分板机网址:http://www.yushunli.com
                                        苏州宇顺力电子有限公司 版权所有 @ Copyright 2015 联系人:刘小姐 地址:江苏省苏州市昆山市金阳东路1068号(国瑞产业园)*本站相关网页素材及相关资源均来源互联网,如有侵权请速告知,我们将会在24小时内删除* 《中华人民共和国电信与信息服务业务经营许可证》编号:苏ICP备14049770号-5